NOx Sensor 29650-84320

BG 201159 (OE 29650-84320): function on the vehicle

NOx Sensor 29650-84320 is supplied by BEST GROWTH under part number 201159, cross-referenced to OE 29650-84320, as a direct-fit aftermarket nox sensors. In service it measures nitrogen-oxide concentration and residual oxygen in the exhaust stream and reports both values to the aftertreatment controller over the vehicle data bus. Upstream and downstream readings together set DEF dosing quantity and score SCR conversion efficiency.

BG 201159 is built to the position defined by its OE application on a 24V electrical system on the platform from Hyundai. Position, calibration and connector layout are part of the specification, so a part that physically fits is not automatically the correct part.

Cable length and connector keying are part of the specification. A cell with correct electrical output but the wrong lead length will not route to the OE bracket.

Fitment for Hyundai and OE cross reference

BG 201159 replaces 2 OE references: 29650-84320 and 5WK9 7302, covering cross applications. Always confirm the number printed on the removed part, including any supersession issued by the vehicle manufacturer.

Recorded vehicle coverage for 201159 includes Hyundai, typically on Xcient / Trago Truck. Coverage lists are a starting point for identification, not a substitute for checking the OE number on the vehicle.

Where several OE numbers appear against one BG reference, they are supersessions or regional variants of the same specification. Ordering by 29650-84320 and quoting the number on your part lets our technical team confirm the variant before despatch.

Symptoms that lead to replacing 29650-84320

These complaints bring a vehicle in with the Hyundai nox sensors under suspicion. None of them prove BG 201159 has failed on its own, which is why the checks below matter before a replacement is ordered.

• DEF over-consumption with no visible leak
• torque derate or speed inducement with a full, in-spec DEF tank
• no communication with the sensor control module after a cold start
• sensor value frozen at a fixed number once the exhaust warms up
• dosing shut-down after a few minutes of steady-state running

Checks before fitting BG 201159

Aftertreatment faults are usually system faults. Working through these checks prevents a repeat failure after the new nox sensors is fitted.

• Compare upstream and downstream NOx readings warmed and under load — idle values prove nothing.
• Confirm supply voltage, ground quality and bus termination before condemning the sensor module.
• Inspect the harness for heat damage and the connector for moisture and green corrosion.
• Check for exhaust leaks ahead of the sensor boss; a diluted sample reads low NOx.
• Read the sensor's own dew-point release time — a cell that never heats is a supply or module fault.

Quality, packaging and ordering 201159

BG 201159 is manufactured and tested to aftermarket replacement standards, with electrical, leakage and functional testing carried out before packing on the 24V specification. Bulk and retail packaging, private-label cartons and customer-specific labelling are available for distributors and workshop groups.

Send OE 29650-84320 or the number printed on your part, the engine code and the vehicle identification number with your enquiry, and our technical team will confirm the correct reference, current stock position and lead time before you commit to an order.

Frequently asked questions

Does BG 201159 replace OE 29650-84320?

Yes. BG 201159 is listed against 29650-84320 and 5WK9 7302. Confirm the number printed on the removed part and any manufacturer supersession before ordering.

Which vehicles does BG 201159 fit?

Recorded coverage includes Hyundai. It is supplied as a direct-fit aftermarket nox sensors on 24V systems. Adaptation, reset or relearn procedures required by the vehicle manufacturer still apply after installation.

Does this fault code always mean the nox sensors has failed?

No. Exhaust leaks, wiring and connector damage, reductant quality, dosing performance and upstream engine faults can all produce the same codes. Validate those inputs before replacing BG 201159.